Call (610) 767-7110

Jeep

/Jeep

We Service and Repair Most Jeep Cars and Trucks

2014 Jeep Patriot

2023-10-06T22:04:09+00:00

Jeep Patriot

Mileage
54,385
Service Date
10/4/2023
Services Performed
  • Check the vehicles under hood fluid levels and remove the oil fill cap and breather assemblies (where applicable) Remove the vehicles engine oil drain plug, and drain the contents of the engines oil pan or sump. Remove the filter assembly and clean the sealing surfaces of the housing for reinstallation. On cartridge equipped vehicles, replace the housing O rings and clean the debris from the housing and relief valves. Lubricate the O rings on the housing and or the filter assembly and replace the filter or element. Clean and inspect the oil drain plug gasket, and check the threads in the engines oil pan. Torque the plug to the manufacturers specification using a new gasket where required. Clean the grease zerks to remove debris, and lubricate all accessible fittings on the vehicles steering, suspension, driveline and chassis components. Check and or set the tire pressures and relearn the TPMS system where required. Fill the engine with the manufacturers specified type, grade, and viscosity engine oil and verify level after purging the new filter. Check and or top off all low fluid levels and reset the maintenance reminder system where applicable. Note. Some vehicles maintenance reminders do not take on initial reset. If your maintenance light happens to come on following an oil service, please give us a call so we can correct it.
 
Charlie N. gave our service a 5 star review on 10/5/2023
2014 Jeep Patriot 2023-10-06T22:04:09+00:00

2012 Jeep Liberty

2023-08-07T22:00:50+00:00

Jeep Liberty

Mileage
176,261
Service Date
7/31/2023
Services Performed
  • Check the vehicles under hood fluid levels and remove the oil fill cap and breather assemblies (where applicable) Remove the vehicles engine oil drain plug, and drain the contents of the engines oil pan or sump. Remove the filter assembly and clean the sealing surfaces of the housing for reinstallation. On cartridge equipped vehicles, replace the housing O rings and clean the debris from the housing and relief valves. Lubricate the O rings on the housing and or the filter assembly and replace the filter or element. Clean and inspect the oil drain plug gasket, and check the threads in the engines oil pan. Torque the plug to the manufacturers specification using a new gasket where required. Clean the grease zerks to remove debris, and lubricate all accessible fittings on the vehicles steering, suspension, driveline and chassis components. Check and or set the tire pressures and relearn the TPMS system where required. Fill the engine with the manufacturers specified type, grade, and viscosity engine oil and verify level after purging the new filter. Check and or top off all low fluid levels and reset the maintenance reminder system where applicable. Note. Some vehicles maintenance reminders do not take on initial reset. If your maintenance light happens to come on following an oil service, please give us a call so we can correct it.
  • Road test vehicle and check for brake pulsation, brake noise, wheel alignment pull, steering wheel centering, suspension stability, tire balance condition, transmission shifting and or clutch engagement, and engine performance concerns. Visually inspect tires for wear resulting from alignment, or balance problems. Check front and rear suspension components for wear at all visible bushings, pivots, sockets, and joints. Check the condition of all drive belts, radiator hoses, heater hoses, brake hoses, and verify level and condition of engine coolant is good. Check engine, transmission, final drive, and differentials for any oil leaks. Check CV drive axle boots for cracks or tears. Check ignition system components consisting of plugs, ignition wires, coils, and or cap and rotor if applicable. Check exhaust system fittings, clamps, and gaskets for leaks or damage and verify condition and levels of power steering fluid, brake fluid, transmission fluid, and differential or final drive fluid. Test all vehicle exterior lights for illumination, turn signal operation, and emergency flasher operation. Hook vehicles components to the VAT45 digital analyzer. Perform a full electrical system diagnostic including a complete analysis of starting and charging system components; vehicle battery (connections and cables), alternator output (belt tension and condition), and starter operation.
 
Linda B. gave our service a 5 star review on 8/6/2023
2012 Jeep Liberty 2023-08-07T22:00:50+00:00

2019 Jeep Grand Cherokee

2023-07-07T22:04:12+00:00

Jeep Grand Cherokee

Mileage
48,321
Service Date
7/6/2023
Services Performed
  • Check the vehicles under hood fluid levels and remove the oil fill cap and breather assemblies (where applicable) Remove the vehicles engine oil drain plug, and drain the contents of the engines oil pan or sump. Remove the filter assembly and clean the sealing surfaces of the housing for reinstallation. On cartridge equipped vehicles, replace the housing O rings and clean the debris from the housing and relief valves. Lubricate the O rings on the housing and or the filter assembly and replace the filter or element. Clean and inspect the oil drain plug gasket, and check the threads in the engines oil pan. Torque the plug to the manufacturers specification using a new gasket where required. Clean the grease zerks to remove debris, and lubricate all accessible fittings on the vehicles steering, suspension, driveline and chassis components. Check and or set the tire pressures and relearn the TPMS system where required. Fill the engine with the manufacturers specified type, grade, and viscosity engine oil and verify level after purging the new filter. Check and or top off all low fluid levels and reset the maintenance reminder system where applicable. Note. Some vehicles maintenance reminders do not take on initial reset. If your maintenance light happens to come on following an oil service, please give us a call so we can correct it.
 
Douglas V. gave our service a 5 star review on 7/6/2023
2019 Jeep Grand Cherokee 2023-07-07T22:04:12+00:00

2011 Jeep Wrangler

2023-06-30T22:05:33+00:00

Jeep Wrangler

Mileage
117,242
Service Date
6/29/2023
Services Performed
  • Remove all components that interfere with the removal of the vehicles transaxle assembly. Remove all shifter linkages and any electrical connectors from the transaxle. Remove the lower cross member and the vehicles drive axles. Remove all bell housing bolts and support the vehicles engine to remove the transaxle from the vehicle. Remove the clutch assembly and clean the inside of the bell housing to remove debris. Lubricate all pivot points and the land where the throw out bearing is positioned. Replace the clutch disc, pressure plate, throw out bearing, and pilot bearing. Reassemble all components and center the vehicles drive line. Drain the vehicles transaxle fluid and replace with new fluid. Evacuate and replace all of the clutch hydraulic fluid and top off the transaxle. Make any necessary adjustments to the shift cable to ensure proper clutch engagement/disengagement. (if applicable) Road test the vehicle and check for leaks and for proper clutch operation.
  • Install data scanner and engine analyzer. Run tests on the body controller and anti lock braking system computer control units. Remove fault codes from the processors memory. Codes exist in the system for rear abs sensors. Perform all necessary pin point tests checking the wiring, grounds, relays, and related circuit components to isolate the problem to the rear sensors. Remove and replace the rear ABS sensor and replace the wiring.
 
Laura B. gave our service a 5 star review on 6/29/2023
2011 Jeep Wrangler 2023-06-30T22:05:33+00:00

2008 Jeep Compass

2023-06-22T22:03:24+00:00

Jeep Compass

Mileage
167,161
Service Date
6/21/2023
Services Performed
  • Check the vehicles under hood fluid levels and remove the oil fill cap and breather assemblies (where applicable) Remove the vehicles engine oil drain plug, and drain the contents of the engines oil pan or sump. Remove the filter assembly and clean the sealing surfaces of the housing for reinstallation. On cartridge equipped vehicles, replace the housing O rings and clean the debris from the housing and relief valves. Lubricate the O rings on the housing and or the filter assembly and replace the filter or element. Clean and inspect the oil drain plug gasket, and check the threads in the engines oil pan. Torque the plug to the manufacturers specification using a new gasket where required. Clean the grease zerks to remove debris, and lubricate all accessible fittings on the vehicles steering, suspension, driveline and chassis components. Check and or set the tire pressures and relearn the TPMS system where required. Fill the engine with the manufacturers specified type, grade, and viscosity engine oil and verify level after purging the new filter. Check and or top off all low fluid levels and reset the maintenance reminder system where applicable. Note. Some vehicles maintenance reminders do not take on initial reset. If your maintenance light happens to come on following an oil service, please give us a call so we can correct it.
  • Remove the cabin air housing to access the interior cabin air filter. This filter is responsible for filtering the air used for the heating and air conditioning in the vehicle and removing harmful particulates. Vacuum the inside of the filters housing and replace the cabin air filter with a new unit. Reinstall the access covers and test the air flow from the vents.
  • Remove the air intake hose from the plenum chamber and disassemble the filter housing. Remove the existing engine air filter and vacuum the inside of the filter housing. Install the replacement filter and resecure the air intake pipes to the plenum chamber.
 
Edward D. gave our service a 5 star review on 6/21/2023
2008 Jeep Compass 2023-06-22T22:03:24+00:00

2008 Jeep Compass

2022-12-22T23:00:34+00:00

Jeep Compass

Mileage
164,374
Service Date
12/21/2022
Services Performed
  • Check the vehicles under hood fluid levels and remove the oil fill cap and breather assemblies (where applicable) Remove the vehicles engine oil drain plug, and drain the contents of the engines oil pan or sump. Remove the filter assembly and clean the sealing surfaces of the housing for reinstallation. On cartridge equipped vehicles, replace the housing O rings and clean the debris from the housing and relief valves. Lubricate the O rings on the housing and or the filter assembly and replace the filter or element. Clean and inspect the oil drain plug gasket, and check the threads in the engines oil pan. Torque the plug to the manufacturers specification using a new gasket where required. Clean the grease zerks to remove debris, and lubricate all accessible fittings on the vehicles steering, suspension, driveline and chassis components. Check and or set the tire pressures and relearn the TPMS system where required. Fill the engine with the manufacturers specified type, grade, and viscosity engine oil and verify level after purging the new filter. Check and or top off all low fluid levels and reset the maintenance reminder system where applicable. Note. Some vehicles maintenance reminders do not take on initial reset. If your maintenance light happens to come on following an oil service, please give us a call so we can correct it.
 
Edward D. gave our service a 5 star review on 12/21/2022
2008 Jeep Compass 2022-12-22T23:00:34+00:00

2016 Jeep Grand Cherokee

2022-12-04T22:59:15+00:00

Jeep Grand Cherokee

Mileage
36,243
Service Date
12/3/2022
Services Performed
  • Check brakes
 
Todd G. gave our service a 5 star review on 12/3/2022
2016 Jeep Grand Cherokee 2022-12-04T22:59:15+00:00

2008 Jeep Compass

2022-07-15T22:02:59+00:00

Jeep Compass

Mileage
161,581
Service Date
7/14/2022
Services Performed
  • Check the vehicles under hood fluid levels and remove the oil fill cap and breather assemblies (where applicable) Remove the vehicles engine oil drain plug, and drain the contents of the engines oil pan or sump. Remove the filter assembly and clean the sealing surfaces of the housing for reinstallation. On cartridge equipped vehicles, replace the housing O rings and clean the debris from the housing and relief valves. Lubricate the O rings on the housing and or the filter assembly and replace the filter or element. Clean and inspect the oil drain plug gasket, and check the threads in the engines oil pan. Torque the plug to the manufacturers specification using a new gasket where required. Clean the grease zerks to remove debris, and lubricate all accessible fittings on the vehicles steering, suspension, driveline and chassis components. Check and or set the tire pressures and relearn the TPMS system where required. Fill the engine with the manufacturers specified type, grade, and viscosity engine oil and verify level after purging the new filter. Check and or top off all low fluid levels and reset the maintenance reminder system where applicable. Note. Some vehicles maintenance reminders do not take on initial reset. If your maintenance light happens to come on following an oil service, please give us a call so we can correct it.
 
Edward D. gave our service a 5 star review on 7/14/2022
2008 Jeep Compass 2022-07-15T22:02:59+00:00

2008 Jeep Compass

2021-10-09T22:03:15+00:00

Jeep Compass

Mileage
157,000
Service Date
10/8/2021
Services Performed
  • Replace the Passenger Side Front Marker Lens.
 
Edward D. gave our service a 5 star review on 10/8/2021
2008 Jeep Compass 2021-10-09T22:03:15+00:00

2015 Jeep Grand Cherokee

2021-10-06T22:03:40+00:00

Jeep Grand Cherokee

Mileage
88,041
Service Date
10/5/2021
Services Performed
  • Install Performance Upgrade and Program the Computer With Updated Parameters.
 
Gary T. gave our service a 5 star review on 10/5/2021
2015 Jeep Grand Cherokee 2021-10-06T22:03:40+00:00