Mercury

Home / Mercury

We Service and Repair all Mercury cars

  • 2004 Mercury Mountaineer

    Mercury Mountaineer
    Mileage
    206,439
    Service Date
    4/29/2022
    Services Performed
    • Check the vehicles under hood fluid levels and remove the oil fill cap and breather assemblies (where applicable) Remove the vehicles engine oil drain plug, and drain the contents of the engines oil pan or sump. Remove the filter assembly and clean the sealing surfaces of the housing for reinstallation. On cartridge equipped vehicles, replace the housing O rings and clean the debris from the housing and relief valves. Lubricate the O rings on the housing and or the filter assembly and replace the filter or element. Clean and inspect the oil drain plug gasket, and check the threads in the engines oil pan. Torque the plug to the manufacturers specification using a new gasket where required. Clean the grease zerks to remove debris, and lubricate all accessible fittings on the vehicles steering, suspension, driveline and chassis components. Check and or set the tire pressures and relearn the TPMS system where required. Fill the engine with the manufacturers specified type, grade, and viscosity engine oil and verify level after purging the new filter. Check and or top off all low fluid levels and reset the maintenance reminder system where applicable. Note. Some vehicles maintenance reminders do not take on initial reset. If your maintenance light happens to come on following an oil service, please give us a call so we can correct it.
     
    John A. gave our service a 5 star review on 4/30/2022
  • 2004 Mercury Mountaineer

    Mercury Mountaineer
    Mileage
    204,185
    Service Date
    6/19/2021
    Services Performed
    • Check the vehicles under hood fluid levels and remove the oil fill cap and breather assemblies (where applicable) Remove the vehicles engine oil drain plug, and drain the contents of the engines oil pan or sump. Remove the filter assembly and clean the sealing surfaces of the housing for reinstallation. On cartridge equipped vehicles, replace the housing O rings and clean the debris from the housing and relief valves. Lubricate the O rings on the housing and or the filter assembly and replace the filter or element. Clean and inspect the oil drain plug gasket, and check the threads in the engines oil pan. Torque the plug to the manufacturers specification using a new gasket where required. Clean the grease zerks to remove debris, and lubricate all accessible fittings on the vehicles steering, suspension, driveline and chassis components. Check and or set the tire pressures and relearn the TPMS system where required. Fill the engine with the manufacturers specified type, grade, and viscosity engine oil and verify level after purging the new filter. Check and or top off all low fluid levels and reset the maintenance reminder system where applicable. Note. Some vehicles maintenance reminders do not take on initial reset. If your maintenance light happens to come on following an oil service, please give us a call so we can correct it.
    • Install data scanner and engine analyzer. Run tests on the fuel, ignition, and computer control systems. Retrieve fault codes from the processors memory. Codes exist in the system for insufficient EGR flow (P0401). Perform all necessary pin point tests checking the wiring, grounds, relays, and related circuit components to isolate the problem to the electronic EGR valve assembly being faulty which will need to be replaced in order to repair the issue.
    • Road test vehicle and check for brake pulsation, brake noise, wheel alignment pull, steering wheel centering, suspension stability, tire balance condition, transmission shifting and or clutch engagement, and engine performance concerns. Visually inspect tires for wear resulting from alignment, or balance problems. Check front and rear suspension components for wear at all visible bushings, pivots, sockets, and joints. Check the condition of all drive belts, radiator hoses, heater hoses, brake hoses, and verify level and condition of engine coolant is good. Check engine, transmission, final drive, and differentials for any oil leaks. Check CV drive axle boots for cracks or tears. Check ignition system components consisting of plugs, ignition wires, coils, and or cap and rotor if applicable. Check exhaust system fittings, clamps, and gaskets for leaks or damage and verify condition and levels of power steering fluid, brake fluid, transmission fluid, and differential or final drive fluid. Test all vehicle exterior lights for illumination, turn signal operation, and emergency flasher operation. Hook vehicles components to the VAT45 digital analyzer. Perform a full electrical system diagnostic including a complete analysis of starting and charging system components; vehicle battery (connections and cables), alternator output (belt tension and condition), and starter operation.
     
    John A. gave our service a 5 star review on 7/5/2021
  • 2004 Mercury Mountaineer

    Mercury Mountaineer
    Mileage
    203,024
    Service Date
    3/20/2021
    Services Performed
    • Check brake systems hydraulic system components for leaks. Found that drivers side, front section of line has failed and will need to be repaired to fix the issue. Remove all damaged line sections and reshape replacement lines to fit. Install new lines, clips, brackets, and unions to replace bad sections. Perform full brake system fluid flush to remove contaminants and air from the system. Adjust rear brakes and parking brake assemblies if applicable and top off reservoir with new fluid. Perform pressure test to check system for leaks and road test for proper operation.
    • Found that the sealing bead was leaking as well as the valve stem. Repair both leaks and check and set all tire pressures to the specified amount.
    • Remove the front steering and suspension system components. Disconnect the sway bar assembly and links. Remove the fasteners from the ball joints and bushings. Clean all hardware and rethread as necessary. Clean the chassis mounting points and install new control arm assembly. Lubricate all pivots and torque the hardware to specification. Reassemble the sway bar links and bushing assemblies and reattach and torque the spindle. Reinstall steering components check and or set all tire pressures. Install 4 laser heads on vehicle and take initial measurements. Adjust factory toe angle to specification. Note: Shims, Eccentrics and labor for fixed alignment angles in both the front and the rear are not included.
    • Road test the vehicle to verify any alignment concerns. Check and or set all tire pressures. Install targets on the vehicles wheels, and take initial alignment measurements. Adjust the factory toe angle to specification, and verify that the other alignment angles on both the front and rear axles are within specifications. Note: Shims, Eccentrics and labor for fixed alignment angles in both the front and the rear are not included.
     
    John A. gave our service a 5 star review on 3/27/2021
  • 2009 Mercury Milan

    Mercury Milan
    Mileage
    127,623
    Service Date
    6/24/2019
    Services Performed
    • Check the vehicles under hood fluid levels and remove the oil fill cap and breather assemblies (where applicable) Remove the vehicles engine oil drain plug, and drain the contents of the engines oil pan or sump. Remove the filter assembly and clean the sealing surfaces of the housing for reinstallation. On cartridge equipd vehicles, replace the housing O rings and clean the debris from the housing and relief valves. Lubricate the O rings on the housing and or the filter assembly and replace the filter or element. Clean and inspect the oil drain plug gasket, and check the threads in the engines oil pan. Torque the plug to the manufacturers specification using a new gasket where required. Clean the grease zerks to remove debris, and lubricate all accessible fittings on the vehicles steering, suspension, driveline and chassis components. Check and or set the tire pressures and relearn the TPMS system where required. Fill the engine with the manufactures specified type, grade, and viscosity engine oil and verify level after purging the new filter. Check and or top off all low fluid levels and reset the maintenance reminder system where applicable. Note. Some vehicles maintenance reminders do not take on initial reset. If your maintenance light happens to come on following an oil service, please give us a call so we can correct it.
     
    Mike M. gave our service a 5 star review on 6/25/2019