Mazda Archives - Car Doc, Inc

2024 Mazda CX-5
Mileage
17,046
Service Date
9/3/2026
Services Performed
Check the vehicles under hood fluid levels and remove the oil fill cap and breather assemblies (where applicable) Remove the vehicles engine oil drain plug, and drain the contents of the engines oil pan or sump. Remove the filter assembly and clean the sealing surfaces of the housing for reinstallation. On cartridge equipped vehicles, replace the housing O rings and clean the debris from the housing and relief valves. Lubricate the O rings on the housing and or the filter assembly and replace the filter or element. Clean and inspect the oil drain plug gasket, and check the threads in the engines oil pan. Torque the plug to the manufacturers specification using a new gasket where required. Clean the grease zerks to remove debris, and lubricate all accessible fittings on the vehicles steering, suspension, driveline and chassis components. Check and or set the tire pressures and relearn the TPMS system where required. Fill the engine with the manufacturers specified type, grade, and viscosity engine oil and verify level after purging the new filter. Check and or top off all low fluid levels and reset the maintenance reminder system where applicable. Note. Some vehicles maintenance reminders do not take on initial reset. If your maintenance light happens to come on following an oil service, please give us a call so we can correct it.
Edward D. gave our service a 5 star review on 9/3/2026
2011 Mazda CX-7
Mileage
106,402
Service Date
12/29/2025
Services Performed
Remove necessary brackets and covers to access the vehicles battery. Remove both battery cables and clean the terminal ends. Remove the existing battery and clean all surrounding components and the battery tray to remove any residual acid. Apply corrosion inhibitor to the tray and install a new battery. Reinstall hold down and tighten the battery cables. Check all electrical system components for proper operation and perform a full electrical system analysis.
Shelley M. gave our service a 5 star review on 12/29/2025
2024 Mazda CX-5
Mileage
9,694
Service Date
6/26/2025
Services Performed
Check the vehicles under hood fluid levels and remove the oil fill cap and breather assemblies (where applicable) Remove the vehicles engine oil drain plug, and drain the contents of the engines oil pan or sump. Remove the filter assembly and clean the sealing surfaces of the housing for reinstallation. On cartridge equipped vehicles, replace the housing O rings and clean the debris from the housing and relief valves. Lubricate the O rings on the housing and or the filter assembly and replace the filter or element. Clean and inspect the oil drain plug gasket, and check the threads in the engines oil pan. Torque the plug to the manufacturers specification using a new gasket where required. Clean the grease zerks to remove debris, and lubricate all accessible fittings on the vehicles steering, suspension, driveline and chassis components. Check and or set the tire pressures and relearn the TPMS system where required. Fill the engine with the manufacturers specified type, grade, and viscosity engine oil and verify level after purging the new filter. Check and or top off all low fluid levels and reset the maintenance reminder system where applicable. Note. Some vehicles maintenance reminders do not take on initial reset. If your maintenance light happens to come on following an oil service, please give us a call so we can correct it.
Remove the four tires from the vehicle, and clean the wheel studs, hub flanges, and the rims centric. Check the vehicles braking system components for wear, remaining brake material, and signs of pending issues. Reinstall the tires onto the vehicle in their best suited locations based on overall wear, torquing all lugs to factory specification. Inflate all tires to the manufacturers suggested pressure, and visually assess the tread for abnormal wear which may indicate a need for a wheel alignment. Reset the vehicles tire pressure monitor sensor locations where required, using the factory approved TPMS (Tire Pressure Monitoring) system, scan tool. Road test the vehicle and confirm there is no abnormal handling characteristics following the rotation. Note: Some vehicles may have a slight drift following a tire rotation. This is due to a pattern that developes in some tires due to excessive time in one location. This condition should improve as the tread conforms to the new location / alignment angle. If drifting would not improve, sometimes an alignment or a cross rotation is required.
Edward D. gave our service a 5 star review on 6/26/2025
2024 Mazda CX-5
Mileage
4,859
Service Date
9/16/2024
Services Performed
Check the vehicles under hood fluid levels and remove the oil fill cap and breather assemblies (where applicable) Remove the vehicles engine oil drain plug, and drain the contents of the engines oil pan or sump. Remove the filter assembly and clean the sealing surfaces of the housing for reinstallation. On cartridge equipped vehicles, replace the housing O rings and clean the debris from the housing and relief valves. Lubricate the O rings on the housing and or the filter assembly and replace the filter or element. Clean and inspect the oil drain plug gasket, and check the threads in the engines oil pan. Torque the plug to the manufacturers specification using a new gasket where required. Clean the grease zerks to remove debris, and lubricate all accessible fittings on the vehicles steering, suspension, driveline and chassis components. Check and or set the tire pressures and relearn the TPMS system where required. Fill the engine with the manufacturers specified type, grade, and viscosity engine oil and verify level after purging the new filter. Check and or top off all low fluid levels and reset the maintenance reminder system where applicable. Note. Some vehicles maintenance reminders do not take on initial reset. If your maintenance light happens to come on following an oil service, please give us a call so we can correct it.
Edward D. gave our service a 5 star review on 9/16/2024
2016 Mazda 3
Mileage
78,814
Service Date
8/20/2024
Services Performed
Road test vehicle and check for brake pulsation, brake noise, wheel alignment pull, steering wheel centering, suspension stability, tire balance condition, transmission shifting and or clutch engagement, and engine performance concerns. Visually inspect tires for wear resulting from alignment, or balance problems. Check front and rear suspension components for wear at all visible bushings, pivots, sockets, and joints. Check the condition of all drive belts, radiator hoses, heater hoses, brake hoses, and verify level and condition of engine coolant is good. Check engine, transmission, final drive, and differentials for any oil leaks. Check CV drive axle boots for cracks or tears. Check ignition system components consisting of plugs, ignition wires, coils, and or cap and rotor if applicable. Check exhaust system fittings, clamps, and gaskets for leaks or damage and verify condition and levels of power steering fluid, brake fluid, transmission fluid, and differential or final drive fluid. Test all vehicle exterior lights for illumination, turn signal operation, and emergency flasher operation. Hook vehicles components to the VAT45 digital analyzer. Perform a full electrical system diagnostic including a complete analysis of starting and charging system components; vehicle battery (connections and cables), alternator output (belt tension and condition), and starter operation.
Jeff M. gave our service a 5 star review on 8/21/2024
2016 Mazda 6
Mileage
111,788
Service Date
7/8/2024
Services Performed
Remove the cabin air housing to access the interior cabin air filter. This filter is responsible for filtering the air used for the heating and air conditioning in the vehicle and removing harmful particulates. Vacuum the inside of the filters housing and replace the cabin air filter with a new unit. Reinstall the access covers and test the air flow from the vents.
Remove the air intake hose from the plenum chamber and disassemble the filter housing. Remove the existing engine air filter and vacuum the inside of the filter housing. Install the replacement filter and resecure the air intake pipes to the plenum chamber.
Check the vehicles under hood fluid levels and remove the oil fill cap and breather assemblies (where applicable) Remove the vehicles engine oil drain plug, and drain the contents of the engines oil pan or sump. Remove the filter assembly and clean the sealing surfaces of the housing for reinstallation. On cartridge equipped vehicles, replace the housing O rings and clean the debris from the housing and relief valves. Lubricate the O rings on the housing and or the filter assembly and replace the filter or element. Clean and inspect the oil drain plug gasket, and check the threads in the engines oil pan. Torque the plug to the manufacturers specification using a new gasket where required. Clean the grease zerks to remove debris, and lubricate all accessible fittings on the vehicles steering, suspension, driveline and chassis components. Check and or set the tire pressures and relearn the TPMS system where required. Fill the engine with the manufacturers specified type, grade, and viscosity engine oil and verify level after purging the new filter. Check and or top off all low fluid levels and reset the maintenance reminder system where applicable. Note. Some vehicles maintenance reminders do not take on initial reset. If your maintenance light happens to come on following an oil service, please give us a call so we can correct it.
Edward D. gave our service a 5 star review on 7/8/2024
2014 Mazda CX-9
Mileage
166,219
Service Date
4/17/2024
Services Performed
Remove calipers, clips, and bracket assemblies. Remove the rear disc brake pads and clean and lubricate the caliper slides. Disassemble the rear emergency brake components, and clean and lubricate all associated hardware and linkages. Reassemble the emergency brake assemblies, and deglaze the emergency brake shoes. Set the shoe width to fit the inside diameter of the rotor assemblies, and verify the adjustment. Replace the rear brake rotors and install new brake pads. Perform all necessary system adjustments and vacuum bleed the brake calipers. Top off the master cylinder to proper level, and road test vehicle.
Check the vehicles under hood fluid levels and remove the oil fill cap and breather assemblies (where applicable) Remove the vehicles engine oil drain plug, and drain the contents of the engines oil pan or sump. Remove the filter assembly and clean the sealing surfaces of the housing for reinstallation. On cartridge equipped vehicles, replace the housing O rings and clean the debris from the housing and relief valves. Lubricate the O rings on the housing and or the filter assembly and replace the filter or element. Clean and inspect the oil drain plug gasket, and check the threads in the engines oil pan. Torque the plug to the manufacturers specification using a new gasket where required. Clean the grease zerks to remove debris, and lubricate all accessible fittings on the vehicles steering, suspension, driveline and chassis components. Check and or set the tire pressures and relearn the TPMS system where required. Fill the engine with the manufacturers specified type, grade, and viscosity engine oil and verify level after purging the new filter. Check and or top off all low fluid levels and reset the maintenance reminder system where applicable. Note. Some vehicles maintenance reminders do not take on initial reset. If your maintenance light happens to come on following an oil service, please give us a call so we can correct it.
Dan M. gave our service a 5 star review on 4/18/2024
2016 Mazda 6
Mileage
107,254
Service Date
3/5/2024
Services Performed
Check the vehicles under hood fluid levels and remove the oil fill cap and breather assemblies (where applicable) Remove the vehicles engine oil drain plug, and drain the contents of the engines oil pan or sump. Remove the filter assembly and clean the sealing surfaces of the housing for reinstallation. On cartridge equipped vehicles, replace the housing O rings and clean the debris from the housing and relief valves. Lubricate the O rings on the housing and or the filter assembly and replace the filter or element. Clean and inspect the oil drain plug gasket, and check the threads in the engines oil pan. Torque the plug to the manufacturers specification using a new gasket where required. Clean the grease zerks to remove debris, and lubricate all accessible fittings on the vehicles steering, suspension, driveline and chassis components. Check and or set the tire pressures and relearn the TPMS system where required. Fill the engine with the manufacturers specified type, grade, and viscosity engine oil and verify level after purging the new filter. Check and or top off all low fluid levels and reset the maintenance reminder system where applicable. Note. Some vehicles maintenance reminders do not take on initial reset. If your maintenance light happens to come on following an oil service, please give us a call so we can correct it.
Edward D. gave our service a 5 star review on 3/6/2024
2015 Mazda 3
Mileage
88,326
Service Date
10/16/2023
Services Performed
Right rear tire leak and front left
Eileen L. gave our service a 5 star review on 10/16/2023
2014 Mazda CX-9
Mileage
157,688
Service Date
10/7/2023
Services Performed
Check the vehicles under hood fluid levels and remove the oil fill cap and breather assemblies (where applicable) Remove the vehicles engine oil drain plug, and drain the contents of the engines oil pan or sump. Remove the filter assembly and clean the sealing surfaces of the housing for reinstallation. On cartridge equipped vehicles, replace the housing O rings and clean the debris from the housing and relief valves. Lubricate the O rings on the housing and or the filter assembly and replace the filter or element. Clean and inspect the oil drain plug gasket, and check the threads in the engines oil pan. Torque the plug to the manufacturers specification using a new gasket where required. Clean the grease zerks to remove debris, and lubricate all accessible fittings on the vehicles steering, suspension, driveline and chassis components. Check and or set the tire pressures and relearn the TPMS system where required. Fill the engine with the manufacturers specified type, grade, and viscosity engine oil and verify level after purging the new filter. Check and or top off all low fluid levels and reset the maintenance reminder system where applicable. Note. Some vehicles maintenance reminders do not take on initial reset. If your maintenance light happens to come on following an oil service, please give us a call so we can correct it.
Dan M. gave our service a 5 star review on 10/7/2023

Mazda

We Service and Repair all Mazda cars