Honda Archives - Car Doc, Inc

2008 Honda CR-V
Mileage
241,988
Service Date
10/1/2024
Services Performed
Remove front wheels, suspension and braking system components necessary to access the front struts. Remove ABS wheel speed sensors if applicable. Remove interior trunk panel, packing tray, and lower seat back to access the top mounts. Remove strut assemblies and clean both side spindle bores. Lubricate all front suspension system components and check components for wear. Replace top mounting plates, bushings and strut bearings. Replace mounting hardware and torque to specification. Refit new strut assemblies into the vehicles mounts and reassemble removed components. Torque steering, suspension, and braking system components, and reinstall access panels. Reinstall wheel speed sensors and set the sensor air gap. Run ABS system test using the data scanner to insure that the ABS components are working properly. Check and or set all tire pressures. Install 4 laser heads on vehicle and take initial measurements. Adjust factory toe angle to specification. Note: Shims, Eccentrics and labor for fixed alignment angles in both the front and the rear are not included.
Remove the front steering and suspension system components. Disconnect the sway bar assembly and links. Remove the fasteners from the ball joints and bushings. Clean all hardware and rethread as necessary. Clean the chassis mounting points and install new control arm assembly. Lubricate all pivots and torque the hardware to specification. Reassemble the sway bar links and bushing assemblies and reattach and torque the spindle. Reinstall steering components check and or set all tire pressures. Install 4 laser heads on vehicle and take initial measurements. Adjust factory toe angle to specification. Note: Shims, Eccentrics and labor for fixed alignment angles in both the front and the rear are not included.
Road test the vehicle to verify any alignment concerns. Check and or set all tire pressures. Install targets on the vehicles wheels, and take initial alignment measurements. Adjust the factory toe angle to specification, and verify that the other alignment angles on both the front and rear axles are within specifications. Note: Shims, Eccentrics and labor for fixed alignment angles in both the front and the rear are not included.
Remove any necessary components to gain access to the sway bar bushings. Remove all attaching hardware and remove end bushing from vehicle. Clean all bores that the end links attach to, to prevent any unnecessary noises and or accelerated wear of the replacement components. Install the new end bushing and tighten all hardware to specification. Install any previously removed components, back to their original locations and road test the vehicle to verify there are no noises, clunks, or issues associated with the sway bar end links.
Remove the front axles in the differential and slide the axles out of the axle housing. Remove the axle seals from the axle housing and clean any remaining debris from the axle tubes. Inspect the sealing surfaces of the axle assemblies and burnish accordingly to remove any grooves which may have been caused by the seal. Install seal relocation kit into the axle housing (Where applicable) and lubricate the sealing surface of the seal. Install the axles into the differential and reinstall the retaining clips.
Check the vehicles under hood fluid levels and remove the oil fill cap and breather assemblies (where applicable) Remove the vehicles engine oil drain plug, and drain the contents of the engines oil pan or sump. Remove the filter assembly and clean the sealing surfaces of the housing for reinstallation. On cartridge equipped vehicles, replace the housing O rings and clean the debris from the housing and relief valves. Lubricate the O rings on the housing and or the filter assembly and replace the filter or element. Clean and inspect the oil drain plug gasket, and check the threads in the engines oil pan. Torque the plug to the manufacturers specification using a new gasket where required. Clean the grease zerks to re
Walt A. gave our service a 5 star review on 10/1/2024
2007 Honda Ridgeline
Mileage
115,776
Service Date
9/3/2024
Services Performed
STARTER ASSEMBLY – Remove & Replace
Terry S. gave our service a 5 star review on 9/5/2024
2014 Honda CR-V
Mileage
122,546
Service Date
7/22/2024
Services Performed
Disconnect electrical power and deactivate supplemental restraint (air bag) system per manufacturers specification. Remove the vehicles drivers side air bag and horn pad. Remove the electrical connectors and hardware attaching the clock spring to the steering column and remove the existing clock spring. Remove the ignition switch and install a new one. Install the clock spring into position and reinstall all previously removed components back to original configuration. Restore all electrical power and reactivate the supplemental restraint system. Test all functions of the steering column components to ensure proper operation. Scan all computer controlled components to ensure all systems are within parameters.
Randall B. gave our service a 5 star review on 7/22/2024
2016 Honda Civic
Mileage
52,914
Service Date
5/29/2024
Services Performed
Check the vehicles under hood fluid levels and remove the oil fill cap and breather assemblies (where applicable) Remove the vehicles engine oil drain plug, and drain the contents of the engines oil pan or sump. Remove the filter assembly and clean the sealing surfaces of the housing for reinstallation. On cartridge equipped vehicles, replace the housing O rings and clean the debris from the housing and relief valves. Lubricate the O rings on the housing and or the filter assembly and replace the filter or element. Clean and inspect the oil drain plug gasket, and check the threads in the engines oil pan. Torque the plug to the manufacturers specification using a new gasket where required. Clean the grease zerks to remove debris, and lubricate all accessible fittings on the vehicles steering, suspension, driveline and chassis components. Check and or set the tire pressures and relearn the TPMS system where required. Fill the engine with the manufacturers specified type, grade, and viscosity engine oil and verify level after purging the new filter. Check and or top off all low fluid levels and reset the maintenance reminder system where applicable. Note. Some vehicles maintenance reminders do not take on initial reset. If your maintenance light happens to come on following an oil service, please give us a call so we can correct it.
Check Tires
Nancy C. gave our service a 5 star review on 5/31/2024
2014 Honda CR-V
Mileage
118,977
Service Date
4/30/2024
Services Performed
Check the vehicles under hood fluid levels and remove the oil fill cap and breather assemblies (where applicable) Remove the vehicles engine oil drain plug, and drain the contents of the engines oil pan or sump. Remove the filter assembly and clean the sealing surfaces of the housing for reinstallation. On cartridge equipped vehicles, replace the housing O rings and clean the debris from the housing and relief valves. Lubricate the O rings on the housing and or the filter assembly and replace the filter or element. Clean and inspect the oil drain plug gasket, and check the threads in the engines oil pan. Torque the plug to the manufacturers specification using a new gasket where required. Clean the grease zerks to remove debris, and lubricate all accessible fittings on the vehicles steering, suspension, driveline and chassis components. Check and or set the tire pressures and relearn the TPMS system where required. Fill the engine with the manufacturers specified type, grade, and viscosity engine oil and verify level after purging the new filter. Check and or top off all low fluid levels and reset the maintenance reminder system where applicable. Note. Some vehicles maintenance reminders do not take on initial reset. If your maintenance light happens to come on following an oil service, please give us a call so we can correct it.
Randall B. gave our service a 5 star review on 4/30/2024
2006 Honda Pilot
Mileage
101,527
Service Date
1/10/2024
Services Performed
Install data scanner and engine analyzer. Run tests on the fuel, ignition, and computer control systems. Retrieve fault codes from the processors memory. Codes exist in the system for P0300, P0301, P0303, P0304, P0306. Perform all necessary pin point tests checking the wiring, grounds, relays, and related circuit components to isolate the problem to <<<<<<<<>>>>>>>>.
Tyler D. gave our service a 5 star review on 1/10/2024
2008 Honda CR-V
Mileage
232,121
Service Date
1/8/2024
Services Performed
Remove necessary brackets and covers to access the vehicles battery. Remove both battery cables and clean the terminal ends. Remove the existing battery and clean all surrounding components and the battery tray to remove any residual acid. Apply corrosion inhibitor to the tray and install a new battery. Reinstall hold down and tighten the battery cables. Check all electrical system components for proper operation and perform a full electrical system analysis.
Check the vehicles under hood fluid levels and remove the oil fill cap and breather assemblies (where applicable) Remove the vehicles engine oil drain plug, and drain the contents of the engines oil pan or sump. Remove the filter assembly and clean the sealing surfaces of the housing for reinstallation. On cartridge equipped vehicles, replace the housing O rings and clean the debris from the housing and relief valves. Lubricate the O rings on the housing and or the filter assembly and replace the filter or element. Clean and inspect the oil drain plug gasket, and check the threads in the engines oil pan. Torque the plug to the manufacturers specification using a new gasket where required. Clean the grease zerks to remove debris, and lubricate all accessible fittings on the vehicles steering, suspension, driveline and chassis components. Check and or set the tire pressures and relearn the TPMS system where required. Fill the engine with the manufacturers specified type, grade, and viscosity engine oil and verify level after purging the new filter. Check and or top off all low fluid levels and reset the maintenance reminder system where applicable. Note. Some vehicles maintenance reminders do not take on initial reset. If your maintenance light happens to come on following an oil service, please give us a call so we can correct it.
Walt A. gave our service a 5 star review on 1/8/2024
2014 Honda CR-V
Mileage
113,043
Service Date
11/16/2023
Services Performed
Check the vehicles under hood fluid levels and remove the oil fill cap and breather assemblies (where applicable) Remove the vehicles engine oil drain plug, and drain the contents of the engines oil pan or sump. Remove the filter assembly and clean the sealing surfaces of the housing for reinstallation. On cartridge equipped vehicles, replace the housing O rings and clean the debris from the housing and relief valves. Lubricate the O rings on the housing and or the filter assembly and replace the filter or element. Clean and inspect the oil drain plug gasket, and check the threads in the engines oil pan. Torque the plug to the manufacturers specification using a new gasket where required. Clean the grease zerks to remove debris, and lubricate all accessible fittings on the vehicles steering, suspension, driveline and chassis components. Check and or set the tire pressures and relearn the TPMS system where required. Fill the engine with the manufacturers specified type, grade, and viscosity engine oil and verify level after purging the new filter. Check and or top off all low fluid levels and reset the maintenance reminder system where applicable. Note. Some vehicles maintenance reminders do not take on initial reset. If your maintenance light happens to come on following an oil service, please give us a call so we can correct it.
Randall B. gave our service a 5 star review on 11/16/2023
2014 Honda CR-V
Mileage
105,402
Service Date
5/17/2023
Services Performed
Remove necessary shields to access the pressure ports. Install manifold gauges and monitor systems static and dynamic system pressures. Check all air conditioning electrical system components including switch, relays, and pressure switches. Add refrigerant to the system if necessary for leak testing and inject the system with luminescent dye. Check the system for refrigerant leaks using dye detection equipment. Check hoses, clamps, evaporator drain, condenser, receiver dryer, and expansion valve for leaks. The system was low on refrigerant. Recharged the system and checked for leaks. No leaks are visible at this time.
Randall B. gave our service a 5 star review on 5/17/2023
2015 Honda Accord
Mileage
67,180
Service Date
3/16/2023
Services Performed
Hook vehicles components to the VAT45 digital analyzer. Perform a full electrical system diagnostic including a complete analysis of starting and charging system components; vehicle battery (connections and cables), alternator output (belt tension and condition), and starter operation. Remove necessary brackets and covers to access the vehicles battery. Remove both battery cables and clean the terminal ends. Remove the existing battery and clean all surrounding components and the battery tray to remove any residual acid. Apply corrosion inhibitor to the tray and install a new battery. Reinstall hold down and tighten the battery cables. Check all electrical system components for proper operation and perform a full electrical system analysis to reaffirm all systems are operating within specification. Road test vehicle to confirm repairs have been made.
Arthur H. gave our service a 5 star review on 3/16/2023

Honda

We Service and Repair all Honda cars