Chevrolet

Home / Chevrolet / Page 2

We Service and Repair all Chevrolet cars

  • 2007 Chevrolet Equinox

    Chevrolet Equinox
    Mileage
    109,060
    Service Date
    1/3/2023
    Services Performed
    • Check the vehicles under hood fluid levels and remove the oil fill cap and breather assemblies (where applicable) Remove the vehicles engine oil drain plug, and drain the contents of the engines oil pan or sump. Remove the filter assembly and clean the sealing surfaces of the housing for reinstallation. On cartridge equipped vehicles, replace the housing O rings and clean the debris from the housing and relief valves. Lubricate the O rings on the housing and or the filter assembly and replace the filter or element. Clean and inspect the oil drain plug gasket, and check the threads in the engines oil pan. Torque the plug to the manufacturers specification using a new gasket where required. Clean the grease zerks to remove debris, and lubricate all accessible fittings on the vehicles steering, suspension, driveline and chassis components. Check and or set the tire pressures and relearn the TPMS system where required. Fill the engine with the manufacturers specified type, grade, and viscosity engine oil and verify level after purging the new filter. Check and or top off all low fluid levels and reset the maintenance reminder system where applicable. Note. Some vehicles maintenance reminders do not take on initial reset. If your maintenance light happens to come on following an oil service, please give us a call so we can correct it.
    • Unable to locate leak.
    • replace frame brackets, cut out and weld and fabricate new pieces in
     
    Jeff O. gave our service a 5 star review on 1/3/2023
  • 2010 Chevrolet Equinox

    Chevrolet Equinox
    Mileage
    217,039
    Service Date
    1/2/2023
    Services Performed
    • Check the vehicles under hood fluid levels and remove the oil fill cap and breather assemblies (where applicable) Remove the vehicles engine oil drain plug, and drain the contents of the engines oil pan or sump. Remove the filter assembly and clean the sealing surfaces of the housing for reinstallation. On cartridge equipped vehicles, replace the housing O rings and clean the debris from the housing and relief valves. Lubricate the O rings on the housing and or the filter assembly and replace the filter or element. Clean and inspect the oil drain plug gasket, and check the threads in the engines oil pan. Torque the plug to the manufacturers specification using a new gasket where required. Clean the grease zerks to remove debris, and lubricate all accessible fittings on the vehicles steering, suspension, driveline and chassis components. Check and or set the tire pressures and relearn the TPMS system where required. Fill the engine with the manufacturers specified type, grade, and viscosity engine oil and verify level after purging the new filter. Check and or top off all low fluid levels and reset the maintenance reminder system where applicable. Note. Some vehicles maintenance reminders do not take on initial reset. If your maintenance light happens to come on following an oil service, please give us a call so we can correct it.
     
    Bill B. gave our service a 5 star review on 1/2/2023
  • 2005 Chevrolet Silverado

    Chevrolet Silverado
    Mileage
    117,627
    Service Date
    6/22/2022
    Services Performed
    • Lubricate the steering column components to stop the noise. If the problem persists the vehicle should be returned for additional testing.
    • Remove necessary shields to access the pressure ports. Install manifold gauges and monitor systems static and dynamic system pressures. Check all air conditioning electrical system components including switch, relays, and pressure switches. Add refrigerant to the system if necessary for leak testing and inject the system with luminescent dye. Check the system for refrigerant leaks using dye detection equipment. Check hoses, clamps, evaporator drain, condenser, receiver dryer, and expansion valve for leaks. There were no significant leaks found at this time although the receiver dryer appears deteriorated and also they are known for leaks. The customer should return for additional testing if the system gets warm again.
     
    Jeff O. gave our service a 5 star review on 6/22/2022
  • 2018 Chevrolet Silverado 1500

    Chevrolet Silverado 1500
    Mileage
    55,324
    Service Date
    6/14/2022
    Services Performed
    • ALTERNATOR ASSEMBLY – Remove & Replace – V6 – [Includes: Test.]
     
    Danny F. gave our service a 5 star review on 6/21/2022
  • 2012 Chevrolet Cruze

    Chevrolet Cruze
    Mileage
    216,658
    Service Date
    6/1/2022
    Services Performed
    • NOTE: The front bumper components are pushed back towards the engine and were rubbing the lower radiator hose which made it fail prematurely. The front bumper was removed (which was only held on by 2 bolts) to access the radiator/air conditioning components to try and reposition them to prevent contact with the engine components. There was a piece of plastic holding the radiator and condenser towards the engine which was removed and now there is sufficient clearance between the hose and radiator. The customer stated that the vehicle was going to a body shop for repairs so the front bumper was left off and placed in the back of the vehicle. Drain engine coolant and flush system in both directions with water to remove sediment. Hook flush equipment to the vehicles cooling system and forward and reverse flush radiator, heater core, heater control valve, and engine block. Remove the vehicles overflow container and wash out debris. Reinstall overflow and top off to capacity. Run engine on the flush equipment until the engine coolant is clean and the acidity is at an acceptable level. Top off cooling system to capacity with specified amount and type of new engine coolant. Run engine to circulate coolant and check freeze point and acidity to insure a proper mixture is in the system. Run engine to operating temperature and purge air from system. Check to verify that the electric cooling fans are operating within their specified temperature range. Check system for leaks and road test. If the system develops an air pocket, the coolant level may decrease slightly. If this occurs, the customer should return to have the system topped off. NOTE: The engine coolant had a large amount of sludge inside which appears to be intermixed coolant and oil which is a sign there has been an internal failure. It is recommended that this vehicle be addressed for this issue due to the overheating possibilities or with all of the repair work that is needed, it may just be cost effective to purchase another vehicle.
     
    Kerry M. gave our service a 5 star review on 6/1/2022
  • 2005 Chevrolet Tahoe

    Chevrolet Tahoe
    Mileage
    158,828
    Service Date
    5/24/2022
    Services Performed
    • Remove calipers, clips, and bracket assemblies. Remove the rear disc brake pads and clean and lubricate the caliper slides. Disassemble the rear emergency brake components, and clean and lubricate all associated hardware and linkages. Reassemble the emergency brake assemblies, and deglaze the emergency brake shoes. Set the shoe width to fit the inside diameter of the rotor assemblies, and verify the adjustment. Replace the rear brake rotors and install new brake pads. Perform all necessary system adjustments and vacuum bleed the brake calipers. Top off the master cylinder to proper level, and road test vehicle.
    • Remove the vehicles wheel in order to gain access to the passenger side, rear caliper. Remove the brake hose from the caliper and all of the braking components (hardware, brake pads, and slides) for the caliper. Remove the caliper from the vehicle and install the new caliper into position. Reconnect the brake hose to the caliper and lube all slides for the caliper. Install all hardware and tighten to specification. Clean all residual brake fluid from the vehicle and perform a full brake fluid flush in order to remove any contaminants or moisture from the system. Vacuum bleed the system to remove any air or contaminants that remain and road test the vehicle to ensure proper braking and check for leaks.
     
    Robert K. gave our service a 5 star review on 5/25/2022
  • 2012 Chevrolet Silverado

    Chevrolet Silverado
    Mileage
    134,117
    Service Date
    4/29/2022
    Services Performed
    • Check the vehicles under hood fluid levels and remove the oil fill cap and breather assemblies (where applicable) Remove the vehicles engine oil drain plug, and drain the contents of the engines oil pan or sump. Remove the filter assembly and clean the sealing surfaces of the housing for reinstallation. On cartridge equipped vehicles, replace the housing O rings and clean the debris from the housing and relief valves. Lubricate the O rings on the housing and or the filter assembly and replace the filter or element. Clean and inspect the oil drain plug gasket, and check the threads in the engines oil pan. Torque the plug to the manufacturers specification using a new gasket where required. Clean the grease zerks to remove debris, and lubricate all accessible fittings on the vehicles steering, suspension, driveline and chassis components. Check and or set the tire pressures and relearn the TPMS system where required. Fill the engine with the manufacturers specified type, grade, and viscosity engine oil and verify level after purging the new filter. Check and or top off all low fluid levels and reset the maintenance reminder system where applicable. Note. Some vehicles maintenance reminders do not take on initial reset. If your maintenance light happens to come on following an oil service, please give us a call so we can correct it.
    • Replace the Fuel Filter
     
    Kenton J. gave our service a 5 star review on 4/30/2022
  • 2018 Chevrolet Equinox

    Chevrolet Equinox
    Mileage
    90,635
    Service Date
    11/22/2021
    Services Performed
    • Check the vehicles under hood fluid levels and remove the oil fill cap and breather assemblies (where applicable) Remove the vehicles engine oil drain plug, and drain the contents of the engines oil pan or sump. Remove the filter assembly and clean the sealing surfaces of the housing for reinstallation. On cartridge equipped vehicles, replace the housing O rings and clean the debris from the housing and relief valves. Lubricate the O rings on the housing and or the filter assembly and replace the filter or element. Clean and inspect the oil drain plug gasket, and check the threads in the engines oil pan. Torque the plug to the manufacturers specification using a new gasket where required. Clean the grease zerks to remove debris, and lubricate all accessible fittings on the vehicles steering, suspension, driveline and chassis components. Check and or set the tire pressures and relearn the TPMS system where required. Fill the engine with the manufacturers specified type, grade, and viscosity engine oil and verify level after purging the new filter. Check and or top off all low fluid levels and reset the maintenance reminder system where applicable. Note. Some vehicles maintenance reminders do not take on initial reset. If your maintenance light happens to come on following an oil service, please give us a call so we can correct it.
     
    Heath L. gave our service a 5 star review on 11/22/2021
  • 2004 Chevrolet Impala

    Chevrolet Impala
    Mileage
    141,053
    Service Date
    10/2/2021
    Services Performed
    • Check the vehicles under hood fluid levels and remove the oil fill cap and breather assemblies (where applicable) Remove the vehicles engine oil drain plug, and drain the contents of the engines oil pan or sump. Remove the filter assembly and clean the sealing surfaces of the housing for reinstallation. On cartridge equipped vehicles, replace the housing O rings and clean the debris from the housing and relief valves. Lubricate the O rings on the housing and or the filter assembly and replace the filter or element. Clean and inspect the oil drain plug gasket, and check the threads in the engines oil pan. Torque the plug to the manufacturers specification using a new gasket where required. Clean the grease zerks to remove debris, and lubricate all accessible fittings on the vehicles steering, suspension, driveline and chassis components. Check and or set the tire pressures and relearn the TPMS system where required. Fill the engine with the manufacturers specified type, grade, and viscosity engine oil and verify level after purging the new filter. Check and or top off all low fluid levels and reset the maintenance reminder system where applicable. Note. Some vehicles maintenance reminders do not take on initial reset. If your maintenance light happens to come on following an oil service, please give us a call so we can correct it.
     
    Megan M. gave our service a 5 star review on 10/2/2021
  • 2012 Chevrolet Silverado

    Chevrolet Silverado
    Mileage
    132,403
    Service Date
    8/19/2021
    Services Performed
    • Check the vehicles under hood fluid levels and remove the oil fill cap and breather assemblies (where applicable) Remove the vehicles engine oil drain plug, and drain the contents of the engines oil pan or sump. Remove the filter assembly and clean the sealing surfaces of the housing for reinstallation. On cartridge equipped vehicles, replace the housing O rings and clean the debris from the housing and relief valves. Lubricate the O rings on the housing and or the filter assembly and replace the filter or element. Clean and inspect the oil drain plug gasket, and check the threads in the engines oil pan. Torque the plug to the manufacturers specification using a new gasket where required. Clean the grease zerks to remove debris, and lubricate all accessible fittings on the vehicles steering, suspension, driveline and chassis components. Check and or set the tire pressures and relearn the TPMS system where required. Fill the engine with the manufacturers specified type, grade, and viscosity engine oil and verify level after purging the new filter. Check and or top off all low fluid levels and reset the maintenance reminder system where applicable. Note. Some vehicles maintenance reminders do not take on initial reset. If your maintenance light happens to come on following an oil service, please give us a call so we can correct it.
    • Install data scanner and engine analyzer. Run tests on the fuel, ignition, and computer control systems. Retrieve fault codes from the processors memory. Codes exist in the system for (P0442) evap system small leak. Perform all necessary pin point tests checking the wiring, grounds, relays, and related circuit components to isolate the problem to the purge valve assembly sticking intermittently and creating the fault code. Replace the purge valve assembly and clear the fault code in the processors memory. Check the EVAP system for proper operation to confirm repairs.
     
    Gina F. gave our service a 5 star review on 8/19/2021