Call (610) 767-7110

Go to…

Nissan

Home / Nissan

We Service and Repair all Nissan cars

  • 2018 Nissan Rogue Sport

    Nissan Rogue Sport
    Mileage
    103,807
    Service Date
    9/13/2024
    Services Performed
    • Price includes mounting, balancing, flange machining, tire disposal, and resetting / relearning of the tire pressure monitoring systems data, and sensors where necessary.
    • Road test the vehicle to verify any alignment concerns. Check and or set all tire pressures. Install targets on the vehicles wheels, and take initial alignment measurements. Adjust the factory toe angle to specification, and verify that the other alignment angles on both the front and rear axles are within specifications. Note: Shims, Eccentrics and labor for fixed alignment angles in both the front and the rear are not included.
    • Check the vehicles under hood fluid levels and remove the oil fill cap and breather assemblies (where applicable) Remove the vehicles engine oil drain plug, and drain the contents of the engines oil pan or sump. Remove the filter assembly and clean the sealing surfaces of the housing for reinstallation. On cartridge equipped vehicles, replace the housing O rings and clean the debris from the housing and relief valves. Lubricate the O rings on the housing and or the filter assembly and replace the filter or element. Clean and inspect the oil drain plug gasket, and check the threads in the engines oil pan. Torque the plug to the manufacturers specification using a new gasket where required. Clean the grease zerks to remove debris, and lubricate all accessible fittings on the vehicles steering, suspension, driveline and chassis components. Check and or set the tire pressures and relearn the TPMS system where required. Fill the engine with the manufacturers specified type, grade, and viscosity engine oil and verify level after purging the new filter. Check and or top off all low fluid levels and reset the maintenance reminder system where applicable. Note. Some vehicles maintenance reminders do not take on initial reset. If your maintenance light happens to come on following an oil service, please give us a call so we can correct it.
     
    Kevin G. gave our service a 5 star review on 9/14/2024

  • 2019 Nissan Pathfinder

    Nissan Pathfinder
    Mileage
    73,948
    Service Date
    8/20/2024
    Services Performed
    • Check the vehicles under hood fluid levels and remove the oil fill cap and breather assemblies (where applicable) Remove the vehicles engine oil drain plug, and drain the contents of the engines oil pan or sump. Remove the filter assembly and clean the sealing surfaces of the housing for reinstallation. On cartridge equipped vehicles, replace the housing O rings and clean the debris from the housing and relief valves. Lubricate the O rings on the housing and or the filter assembly and replace the filter or element. Clean and inspect the oil drain plug gasket, and check the threads in the engines oil pan. Torque the plug to the manufacturers specification using a new gasket where required. Clean the grease zerks to remove debris, and lubricate all accessible fittings on the vehicles steering, suspension, driveline and chassis components. Check and or set the tire pressures and relearn the TPMS system where required. Fill the engine with the manufacturers specified type, grade, and viscosity engine oil and verify level after purging the new filter. Check and or top off all low fluid levels and reset the maintenance reminder system where applicable. Note. Some vehicles maintenance reminders do not take on initial reset. If your maintenance light happens to come on following an oil service, please give us a call so we can correct it.
    • Visually check the vehicles lighting system to confirm customer condition. After inspection it was found the vehicles <<<>>> side headlight is out. Remove any covers necessary in order to gain access the rear of the headlight housings. Remove the old bulb(s), and clean and tighten the electrical terminals. Install a new headlight bulb, and reattach the electrical connections and locks where necessary. Clean the previously removed hardware and reinstall the removed shields and covers. Test the operation of the vehicles lighting system to confirm that the lighting is operating properly. Verify both high and low beam head lamp alignment using a projection aligner and adjust as required.
     
    Colleen S. gave our service a 5 star review on 8/20/2024

  • 2018 Nissan Rogue Sport

    Nissan Rogue Sport
    Mileage
    83,139
    Service Date
    6/23/2023
    Services Performed
    • Check the vehicles under hood fluid levels and remove the oil fill cap and breather assemblies (where applicable) Remove the vehicles engine oil drain plug, and drain the contents of the engines oil pan or sump. Remove the filter assembly and clean the sealing surfaces of the housing for reinstallation. On cartridge equipped vehicles, replace the housing O rings and clean the debris from the housing and relief valves. Lubricate the O rings on the housing and or the filter assembly and replace the filter or element. Clean and inspect the oil drain plug gasket, and check the threads in the engines oil pan. Torque the plug to the manufacturers specification using a new gasket where required. Clean the grease zerks to remove debris, and lubricate all accessible fittings on the vehicles steering, suspension, driveline and chassis components. Check and or set the tire pressures and relearn the TPMS system where required. Fill the engine with the manufacturers specified type, grade, and viscosity engine oil and verify level after purging the new filter. Check and or top off all low fluid levels and reset the maintenance reminder system where applicable. Note. Some vehicles maintenance reminders do not take on initial reset. If your maintenance light happens to come on following an oil service, please give us a call so we can correct it.
    • Remove the four tires from the vehicle, and clean the wheel studs, hub flanges, and the rims centric. Check the vehicles braking system components for wear, remaining brake material, and signs of pending issues. Reinstall the tires onto the vehicle in their best suited locations based on overall wear, torquing all lugs to factory specification. Inflate all tires to the manufacturers suggested pressure, and visually assess the tread for abnormal wear which may indicate a need for a wheel alignment. Reset the vehicles tire pressure monitor sensor locations where required, using the factory approved TPMS (Tire Pressure Monitoring) system, scan tool. Road test the vehicle and confirm there is no abnormal handling characteristics following the rotation. Note: Some vehicles may have a slight drift following a tire rotation. This is due to a pattern that developes in some tires due to excessive time in one location. This condition should improve as the tread conforms to the new location / alignment angle. If drifting would not improve, sometimes an alignment or a cross rotation is required.
     
    Kevin G. gave our service a 5 star review on 6/28/2023

  • 2009 Nissan Maxima

    Nissan Maxima
    Mileage
    139,478
    Service Date
    6/2/2023
    Services Performed
    • Remove the front steering and suspension system components. Disconnect the sway bar assembly and links. Remove the fasteners from the ball joints and bushings. Clean all hardware and rethread as necessary. Clean the chassis mounting points and install new control arm assembly. Lubricate all pivots and torque the hardware to specification. Reassemble the sway bar links and bushing assemblies and reattach and torque the spindle. Reinstall steering components check and or set all tire pressures. Install 4 laser heads on vehicle and take initial measurements. Adjust factory toe angle to specification. Note: Shims, Eccentrics and labor for fixed alignment angles in both the front and the rear are not included.
    • LATERAL LINK – Remove & Replace – Lower,Rear,One Side
    • Remove the vehicles wheels in order to gain access to the outer tie rod end. Remove any components that interfere with the removal of the tie rod end (braking components, shields). Remove cotter pin and the hardware that attaches the tie rod end to the spindle and adjusting sleeve. Remove the faulty tie rod end and clean the threads in the adjusting sleeve. Apply anti-seize compound to the threads of the new tie rod end and install into the adjusting sleeve and spindle. Tighten all hardware to manufacturers specification and grease all applicable joints on the steering components and reinstall vehicles wheel.
    • Price includes mounting, balancing, flange machining, tire disposal, and resetting / relearning of the tire pressure monitoring systems data, and sensors where necessary.
    • Road test the vehicle to verify any alignment concerns. Check and or set all tire pressures. Install targets on the vehicles wheels, and take initial alignment measurements. Adjust the factory toe angle to specification, and verify that the other alignment angles on both the front and rear axles are within specifications. Note: Shims, Eccentrics and labor for fixed alignment angles in both the front and the rear are not included.
     
    Colin C. gave our service a 5 star review on 6/2/2023

  • 2015 Nissan Pathfinder

    Nissan Pathfinder
    Mileage
    94,506
    Service Date
    1/16/2023
    Services Performed
    • WHEEL HUB – Remove & Replace – Front,One Side – – [Includes: Replace Inner and/or Outer Bearings, Cups, Seals and repack (where applicable).]
     
    Gina F. gave our service a 5 star review on 1/16/2023

  • 2011 Nissan Frontier

    Nissan Frontier
    Mileage
    100,698
    Service Date
    7/10/2021
    Services Performed
    • Remove calipers, clips, and bracket assemblies. Remove the front disc brake pads and front brake rotors and install new brake pads. Perform all necessary system adjustments and vacuum bleed brake calipers. Top off master cylinder to proper level, and road test vehicle.
    • Install data scanner and engine analyzer. Run tests on the fuel, ignition, and computer control systems. Retrieve fault codes from the processors memory. Codes exist in the system for (P0021) intake camshaft timing problem. Perform all necessary pin point tests checking the wiring, grounds, relays, and related circuit components to isolate the problem to the timing chain components needing replacement.
     
    Tom S. gave our service a 5 star review on 7/11/2021

  • 2015 Nissan Rogue

    Nissan Rogue
    Mileage
    78,749
    Service Date
    7/6/2021
    Services Performed
    • Check the vehicles under hood fluid levels and remove the oil fill cap and breather assemblies (where applicable) Remove the vehicles engine oil drain plug, and drain the contents of the engines oil pan or sump. Remove the filter assembly and clean the sealing surfaces of the housing for reinstallation. On cartridge equipped vehicles, replace the housing O rings and clean the debris from the housing and relief valves. Lubricate the O rings on the housing and or the filter assembly and replace the filter or element. Clean and inspect the oil drain plug gasket, and check the threads in the engines oil pan. Torque the plug to the manufacturers specification using a new gasket where required. Clean the grease zerks to remove debris, and lubricate all accessible fittings on the vehicles steering, suspension, driveline and chassis components. Check and or set the tire pressures and relearn the TPMS system where required. Fill the engine with the manufacturers specified type, grade, and viscosity engine oil and verify level after purging the new filter. Check and or top off all low fluid levels and reset the maintenance reminder system where applicable. Note. Some vehicles maintenance reminders do not take on initial reset. If your maintenance light happens to come on following an oil service, please give us a call so we can correct it.
     
    Tony R. gave our service a 5 star review on 7/6/2021

  • 2015 Nissan Rogue

    Nissan Rogue
    Mileage
    73,562
    Service Date
    1/21/2021
    Services Performed
    • Check the vehicles under hood fluid levels and remove the oil fill cap and breather assemblies (where applicable) Remove the vehicles engine oil drain plug, and drain the contents of the engines oil pan or sump. Remove the filter assembly and clean the sealing surfaces of the housing for reinstallation. On cartridge equipped vehicles, replace the housing O rings and clean the debris from the housing and relief valves. Lubricate the O rings on the housing and or the filter assembly and replace the filter or element. Clean and inspect the oil drain plug gasket, and check the threads in the engines oil pan. Torque the plug to the manufacturers specification using a new gasket where required. Clean the grease zerks to remove debris, and lubricate all accessible fittings on the vehicles steering, suspension, driveline and chassis components. Check and or set the tire pressures and relearn the TPMS system where required. Fill the engine with the manufacturers specified type, grade, and viscosity engine oil and verify level after purging the new filter. Check and or top off all low fluid levels and reset the maintenance reminder system where applicable. Note. Some vehicles maintenance reminders do not take on initial reset. If your maintenance light happens to come on following an oil service, please give us a call so we can correct it.
     
    Matt B. gave our service a 5 star review on 1/21/2021

  • 2007 Nissan Murano

    Nissan Murano
    Mileage
    180,484
    Service Date
    11/7/2020
    Services Performed
    • Check the vehicles under hood fluid levels and remove the oil fill cap and breather assemblies (where applicable) Remove the vehicles engine oil drain plug, and drain the contents of the engines oil pan or sump. Remove the filter assembly and clean the sealing surfaces of the housing for reinstallation. On cartridge equipped vehicles, replace the housing O rings and clean the debris from the housing and relief valves. Lubricate the O rings on the housing and or the filter assembly and replace the filter or element. Clean and inspect the oil drain plug gasket, and check the threads in the engines oil pan. Torque the plug to the manufacturers specification using a new gasket where required. Clean the grease zerks to remove debris, and lubricate all accessible fittings on the vehicles steering, suspension, driveline and chassis components. Check and or set the tire pressures and relearn the TPMS system where required. Fill the engine with the manufacturers specified type, grade, and viscosity engine oil and verify level after purging the new filter. Check and or top off all low fluid levels and reset the maintenance reminder system where applicable. Note. Some vehicles maintenance reminders do not take on initial reset. If your maintenance light happens to come on following an oil service, please give us a call so we can correct it.
    • Price includes mounting, balancing, flange machining, tire disposal, and resetting / relearning of the tire pressure monitoring systems data, and sensors.
     
    Nihaet E. gave our service a 5 star review on 11/8/2020