Scion

Home / Scion

We Service and Repair all Scion cars

  • 2013 Scion tC

    Scion tC
    Mileage
    92,532
    Service Date
    3/13/2023
    Services Performed
    • Check the vehicles under hood fluid levels and remove the oil fill cap and breather assemblies (where applicable) Remove the vehicles engine oil drain plug, and drain the contents of the engines oil pan or sump. Remove the filter assembly and clean the sealing surfaces of the housing for reinstallation. On cartridge equipped vehicles, replace the housing O rings and clean the debris from the housing and relief valves. Lubricate the O rings on the housing and or the filter assembly and replace the filter or element. Clean and inspect the oil drain plug gasket, and check the threads in the engines oil pan. Torque the plug to the manufacturers specification using a new gasket where required. Clean the grease zerks to remove debris, and lubricate all accessible fittings on the vehicles steering, suspension, driveline and chassis components. Check and or set the tire pressures and relearn the TPMS system where required. Fill the engine with the manufacturers specified type, grade, and viscosity engine oil and verify level after purging the new filter. Check and or top off all low fluid levels and reset the maintenance reminder system where applicable. Note. Some vehicles maintenance reminders do not take on initial reset. If your maintenance light happens to come on following an oil service, please give us a call so we can correct it.
    • Clean the debris from the engines lower intake, and remove all ignition coil assemblies and spark plugs. Run thread chaser through the cylinder head to remove debris and clean the spark plug hole threads. Clean and tighten the coil terminal connections, and check the weather seals to prevent moisture intrusion. Set the gap of the new plugs to the manufacturers specification and apply anti-seize compound to plug threads. Install the spark plugs and torque to specification. Reinstall the vehicles ignition coils and install the coil connections using dielectric grease. Reinstall any previously removed vacuum, emissions, fuel, and electrical harnesses. Reinstall all ancillary engine brackets, and torque all components to the manufacturers specification. Base idle adjustment is included where applicable. Install data scanner and run engine to operating temperature to verify that all computer controls are operating within parameters. Road test vehicle and verify static ignition timing and applicable fluid levels.
    • Remove any components necessary to gain access to the engines rocker / camshaft covers. Remove all attaching hardware and remove the rocker covers from the cylinder heads. Remove the gasket material from the rocker cover assemblies and clean the channels to remove any remaining residual oil or debris. Clean the mating surfaces on the engines cylinder head(s) and check the surfaces for warpage or any imperfections that would prevent the new gaskets from making a proper seal. Install the new gaskets on to the rocker covers and place onto the cylinder head ensuring that the end seals are secured with sealant. Torque all hardware to manufacturers specification and install any previously removed components back to their original state. Top off the engine oil and or change the engine oil and filter as required. Run the engine to operating temperature and check the rocker covers for leaks.
     
    Matt C. gave our service a 5 star review on 3/15/2023
  • 2006 Scion xB

    Scion xB
    Mileage
    120,039
    Service Date
    12/15/2021
    Services Performed
    • Price includes mounting, balancing, flange machining, tire disposal, and resetting / relearning of the tire pressure monitoring systems data, and sensors.
    • Road test the vehicle to verify any alignment concerns. Check and or set all tire pressures. Install targets on the vehicles wheels, and take initial alignment measurements. Adjust the factory toe angle to specification, and verify that the other alignment angles on both the front and rear axles are within specifications. Note: Shims, Eccentrics and labor for fixed alignment angles in both the front and the rear are not included.
    • Check the vehicles under hood fluid levels and remove the oil fill cap and breather assemblies (where applicable) Remove the vehicles engine oil drain plug, and drain the contents of the engines oil pan or sump. Remove the filter assembly and clean the sealing surfaces of the housing for reinstallation. On cartridge equipped vehicles, replace the housing O rings and clean the debris from the housing and relief valves. Lubricate the O rings on the housing and or the filter assembly and replace the filter or element. Clean and inspect the oil drain plug gasket, and check the threads in the engines oil pan. Torque the plug to the manufacturers specification using a new gasket where required. Clean the grease zerks to remove debris, and lubricate all accessible fittings on the vehicles steering, suspension, driveline and chassis components. Check and or set the tire pressures and relearn the TPMS system where required. Fill the engine with the manufacturers specified type, grade, and viscosity engine oil and verify level after purging the new filter. Check and or top off all low fluid levels and reset the maintenance reminder system where applicable. Note. Some vehicles maintenance reminders do not take on initial reset. If your maintenance light happens to come on following an oil service, please give us a call so we can correct it.
     
    Debra O. gave our service a 5 star review on 12/15/2021